Tuesday, July 23, 2013

Bow fittings

Last weekend I laminated the bow and some tubes on it, the upper one is for a line where I can put a bal fender on like on Thrill Seeker. The other tube is for the side stays of the gennaker pole. The nose will be put on in a later stage because there is not room enough for it at the moment, shaped some foam of the front so the nose can be later put on it without some extra fairing of bow laminate. I did also some farring of the keel line and the stern. At this moment only the stern needs some small pieces of  laminate before we can do the complete outside.

Thursday, July 18, 2013

Back to business


The holiday is over, we arrived last sunday from Croatia where we did have 3 wonderful weeks of sailing.










Before I have to go to real work I was this week still free.
The monday I started with some longboarding and filling the other side, tuesday I did some little longboarding again and put some antifouling on the front of Thrill Seeker and in the afternoon we put Thrill Seeker in the water in his home port. Wednesday and today I did some serious longboarding and filling some low spots. With the longboarding I can lose some weight from the vacation ;-) I started the longboarding with grid 80 but tuesday I switched to grid 40 and that goes very well. On the end of the day I put some carbon on the beam areas and blocked the inspection holes with one layer of carbon so I can easier put the vacuum back on it for the outer layer. The hadges hole was also done with one layer of 250 so I can put the tacky tape on and later put another one over this one and the outside.

Sunday, June 16, 2013

Longboarding for the first time

I did some longboarding with the new flexcat longboard (used sanding paper 80), I was only foam so it was not that hard work but I think with the putty it will be different. The result looked good after some longboarding and I filled the sames and some lows with putty on one side.







Friday, June 7, 2013

making the float hatch entrance

This week I did buy some hatches so I could make the entrance. I carved out the foam for HD inserts for the various pad eyes and the goiot folding cleat and put it in place with som HD putty.



 I did also some repair work on Thrill Seeker this week, I had some leake on the deck so the balsa had to be carved away and filled with glass and putty because this is a place where the lifting eye is placed.
I painted the rudder also today seen in the background on one of the above pictures.





Sunday, June 2, 2013

The taping of the inside for this float is finished

Last week I did some taping of the inside so that is now finished and I put the bow panel and temporary access hole panel  in place. I made also a start with the stern panel.
I had to made the hole for the hatch I little bit smaller because the hatches I had were not strong enough so I did buy another pair on marktplaats.
We did buy also a new multi tool this time a cheap one, for the price of the old one I can buy three of these, it is still a Bosche so I can re-use the blades. I directly used it to cut the foil case, it is now flat with the hull.



 


Sunday, May 26, 2013

taping takes longer than expected

Wednesday and thursday I mounted the rudder web and friday and sunday I tape almost the remaining seams. I have to do only two tapes, one an gused and one in the front on the upside. Friday we also reinforced the underside of the foil case. Saturday and sunday we went for a sail, we should to have a race but there were only three boats and one was not going to race because the wind was too strong for the small boat. We decided not to race with only two boats. We stayed the night on that place with my friend and his boat. Next morning we went home again against the wind in 23kns wind it felt like autumn.

Jaap is preparing his Dragonfly 28








This went broke after 2,5 year
just outside guarantee
Tool for taping the front brush
 on a stick

Monday, May 20, 2013

Fit canting rig option

Yesterday and today we went for a sail with Thrill Seeker, The sunday was not so bad but today we had rain, poor visibility, low temperature and no wind. So we motored to our home harbor and went home. I then decided that I could finish the chainplate, so I did.