Saturday, December 31, 2016

Happy new year

Today Rob did come to help me a hand. We started with the trampoline tubes and this was much easier with the two of us than alone. When we finish routing the tubes we gave the a little sanding with a sanding paper on a tube. The holes are 20 mm wide. We than cut one side of the windows out and went for lunch. After lunch we did the other window side. The next thing was the tubes in the entrance where I put a splash sail in, I do use this also on Thrill Seeker and keeps the boat much dryer and easier accessible. Rob did make a small mold to guide the Multitool so we could easy cut a staid grove in the tube. First we did use a fine blade and after that we use a blade with grid on it to make the grove wider. Rob did smooth the groove with a piece of sanding paper over a rot. In the bottom tube we made a wider entrance for the cloth whit a line in it to enter. Wile Rob was doing that I sanded the windows. In the end we cleaned all the mess we made.

I wish you all a happy new year and a good sailing season.



Friday, December 30, 2016

made a start with cutting side windows and trampoline tubes

I started with looking in the tool shop for a router bit what could cut the trampoline tubes, I could not make up my mind directly what to buy so I first went to the shed to draw a hole on the tube to look if it was big enough. I then marked the places on a tape what I did put on the tube were the holes have to come. I made also a tool for my router where the router slits over on the tube. I sanded the deck before I did get home. On the way home I drove to the tool shop to buy a router bit. In the afternoon I made the first cuts out of the tube. It is handier to do it with two people and the rest have to wait til tomorrow when Rob comes to help and spend new years evening by us. I then did some sanding again but I did find that the primer was not hard enough so I stop with it. Then Fetske did drop by with tea. After the tea break I started with drawing the cutting lines of the windows. I did cut the vertical lines and the tops with a multitool but I left the bottom ones in place so they still are in place so when we cut the tubes tomorrow the most dust stays outside. When the tubes are cut we cut the bottom halves of the windows.

Thursday, December 29, 2016

Put a primer on the upper part of the hull

I took the afternoon free from work to put a white primer on the hull. But we first did take a look at a bigger shed for when the middle hull is finished to store it temporary there and to assemble it together. I than have space to finish the floats and bring it back to the original state. This shed we looked at is not warm enough to finish the floats.
After the lunch we first did some sanding work of the blue filler I put on some spots yesterday and we then primed the hole upper part.

Tuesday, December 27, 2016

Laminating the front of the locker

Yesterday I glue the frond of the locker in place with PU glue. The most of the time went in measuring and fitting. Our dads did came for dinner so I only did a small laminating yob on the cradle before they arrived. I forgot to take pictures.
Today I tape the inside and the outside corners of the locker. I am very satisfied with then result. In the afternoon Fetske did come assist me with sanding the outside upper part of the hull. I think it needs one layer of primer.

Sunday, December 25, 2016

Laminating the side panels to the back panel of the kitchen locker

After a slow start, after all it is Christmastime we went to the shed to make the kitchen locker.
First we unpacked the back panel and it looked very good. Wile I made the back panel to dimensions Fetske did some cleanup. I did find some leftover triplex with carbon on both sides, I decided to use it for the sides and the bottom. First I made a paper template of the sides to get the ride curve with help of the back panel. We then glued the panels together with some PU glue. We then went for a quick lunch. The PU glue was dry when we returned, after some scraping of the glue seams we put a putty filled in the corners and tape it all together with some carbon leftovers. After the tea Fetske went home to do some cooking for tomorrow and I did some sanding by hand because the filler was still not dry enough to use a sander, I went early home to get ready for dinner.



Saturday, December 24, 2016

Laminating the back panel of the kitchen locker

In the morning we started with the back panel. We did this with vacuum because it get nicely pressed to the hull wile it is drying. With the leftover epoxy I did the ends of the hammerhead. After lunch Fetske dremeld the locker edges and filled them with putty. I did put some blue filler on the outside of the hull to get away the ugly spots.



Friday, December 23, 2016

Started at the deck and kitchen floor again

In the morning I started with sanding the cockpit, deck and kitchen floor. After lunch I did cut a hole in the front of the kitchen. This will be a locker for garbage and some other stuff. I formed some foam direct to the hull what will be the back of a sort of drawer. Tomorrow I put some carbon on it. I then did gave the SP unit some Sikaflex on the inside and opened a hole for some tubes for the fridge. As last job I painted the inside of the fridge and the kitchen floor.